Skip to main content

China's J-35 fighter developer develops 3D printing for larger and lighter aircraft structures.


China’s Aviation Industry Corporation of China (AVIC) announced that the Shenyang Aircraft Design and Research Institute, developer of the J-35 stealth fighter, manufactured a 3D-printed metallic load-bearing fuselage structure exceeding 5 meters (16.4 feet) and a four-function annular heat exchanger. Using segmented printing, additive fusion joining, and magnetic polishing, the institute addresses structural deformation, machining limits, and tight internal cooling volumes on modern combat aircraft.


Artist’s rendering of a future British Royal Navy Offshore Support Vessel, designed to serve as a mothership for uncrewed mine-hunting systems. (Picture source: British Royal Navy and editing Army Recognition Group)

China's J-35 developer has produced a 3D-printed central fuselage structure exceeding 5 meters that transfers structural loads, alongside an annular heat exchanger integrating heat transfer, air extraction, load-bearing, and maintenance functions, although it is unclear whether these pieces are intended for the stealth fighter. (Picture source: AVIC)


Key Tactical Insights:

  • Five-Meter Load-Bearing Fuselage Structure: The Shenyang Aircraft Design and Research Institute produced a central fuselage structural component exceeding 5 meters (16.4 feet) in length, designed to transfer primary flight loads. To prevent the thermal distortion and cracking typically associated with large-scale metal printing, engineers printed smaller sections individually and joined them via additive fusion.

  • Four-Function Annular Heat Exchanger: Designed to fit inside the constrained volume of an aircraft air intake, the 3D-printed annular heat exchanger integrates heat transfer, air extraction, structural load-bearing, and maintenance access into a single unit. To smooth internal cooling channels inaccessible to standard tools, the institute developed proprietary magnetic polishing equipment that guides fine steel needles through the passages.

  • Two Decades of Aerospace Additive Experience: According to AVIC, the Shenyang laboratory has spent over 20 years developing six distinct additive manufacturing processes across 13 metal materials and 19 structural component categories for aircraft programs including the J-8, J-11, J-15, and J-35.

  • Strategic Implications for Carrier and Next-Gen Fighters: Consolidating multi-part assemblies and compacting cooling hardware helps conserve internal volume and offset structural weight penalties, factors particularly relevant for carrier-based aircraft like the J-35 operating aboard the Fujian, as well as future combat aircraft designs.


On November 14, 2026, China's Aviation Industry Corporation of China (AVIC) announced that the Shenyang Aircraft Design and Research Institute, developer of the J-35 stealth fighter, had manufactured a metallic load-bearing fuselage structure exceeding 5 meters and an annular heat exchanger integrating four functions through 3D printing. According to the Global Times, the Chinese engineers used segmented printing, additive fusion joining, and magnetic polishing to manufacture components that would otherwise require multiple machining and assembly operations. Shenyang has reportedly developed six additive manufacturing processes, worked with 13 metal material types, and produced 19 categories of aircraft structural components over more than 20 years.

The industrial significance is that both developments address manufacturing constraints encountered in modern combat aircraft such as the J-35: the difficulty of producing large, geometrically complex structures without excessive machining and assembly, and the need to accommodate cooling equipment within increasingly crowded fuselages. Shenyang, which has contributed to more than 40 aircraft models including the J-8, J-11, J-15 and J-35 fighters, manufactured a 3D-printed central fuselage component exceeding 5,000 mm that carries and transfers loads between aircraft structures. Such components must resist wing bending, torsion, and forces transmitted through adjacent fuselage assemblies, although the exact loads carried by Shenyang's component depend on its installation. 

Related Topic: China unveils J-35AE stealth fighter to challenge US F-35 dominance as new buyers emerge

Manufacturing a structure of this size through metal additive processes is difficult as it produces uneven heating, residual stresses, distortion, and cracking, which Shenyang addressed by manufacturing smaller segments and connecting them through additive fusion joining. This approach can also reduce the dependence on a single large printing operation and can eliminate some conventional overlapping joints, fasteners, and alignment operations. However, the fusion-joined regions must withstand the same repeated loading as the surrounding material, while the overall manufacturing benefit still depends on component weight, joining time, inspection requirements, and the number of conventional parts replaced. The 3D-printed annular heat exchanger addresses a separate constraint involving the limited internal volume available for aircraft cooling systems.

Designed for installation inside an air intake, it reportedly combines heat transfer, air extraction, structural load-bearing, and maintenance functions. Its printed internal channels increase the heat-transfer surface area within a fixed installation volume, potentially reducing separate ducts, brackets, and cooling equipment. Because narrow channels create friction and pressure losses, Shenyang developed its own magnetic grinding equipment that moves fine steel needles through the passages using an external magnetic field, thus potentially polishing surfaces inaccessible to conventional tools. This addresses internal roughness that can reduce flow efficiency and complicate cleaning.

How 3D printing could reduce the weight of China's J-35 fighter

For combat aircraft such as the J-35, the potential benefit is to use more compact cooling systems for radar electronics, electronic warfare systems, and onboard processors, although the performance of this annular heat exchanger would still depend on heat-transfer capacity, airflow, pressure drop, and component mass. Weight reduction offers a measurable way to evaluate the industrial benefits of additive manufacturing, although savings vary substantially between components. For instance, Airbus's A320 bionic cabin partition reduced its mass by 45%, saving 30 kg (from 66.7 kg to 36.7 kg), while an A350 titanium bracket achieved a 30% weight reduction. In the U.S., GE Aerospace's LEAP-engine fuel nozzle became 25% lighter by replacing 20 separately manufactured parts with one printed component, demonstrating that 3D printing can also be advantageous for metallic components exposed to demanding thermal conditions.

However, these results depend on topology optimization, which concentrates material along the principal load paths instead of retaining metal in areas where it contributes little to structural resistance. Nevertheless, applied to 100 aircraft components, an average saving of 2 kg through 3D printing would eliminate 200 kg; applied to 250, it would save 500 kg. For carrier fighters such as the J-35, this could offset part of the additional mass needed for the reinforced landing gear, arresting equipment, and other naval requirements, provided the redesigned structures retain their required fatigue resistance and stiffness. Engine manufacturing demonstrates how additive production can also reduce assembly complexity and improve component durability.

GE Aerospace's LEAP fuel nozzle eliminated 19 individual pieces, achieved five times the durability of its predecessor, and has already entered industrial production, with more than 30,000 printed nozzle tips manufactured at Auburn. GE also developed a turbine center frame casing measuring one meter in diameter that consolidated more than 150 individual components into one structure, thus reducing separate manufacturing and joining operations. Aerospace additive manufacturing uses alloys such as the Ti-6Al-4V, which contains 6% aluminum and 4% vanadium with a density of 4.43 g/cm³, and the Inconel 718, a nickel-based superalloy with a density of 8.19 g/cm³. Titanium alloys are suitable for weight-sensitive structural applications, while nickel-based alloys are used where resistance to elevated temperatures and mechanical loading is more important than minimum mass.

How additive manufacturing reduces aircraft production time and material waste

These examples demonstrate two different manufacturing advantages: structural optimization can reduce the amount of metal required, while component consolidation can eliminate joints, welds, and assembly stages. Manufacturing economics provide another measurable comparison. GE's turbine center frame casing project shortened production lead time from more than nine months to 2.5 months, a reduction exceeding 6.5 months or 72%, while simultaneously reducing component weight and manufacturing cost by 30% each. NASA illustrated the material-utilization problem through a titanium aircraft component weighing 300 lb (136 kg) that required a starting billet weighing 6,000 lb (2,722 kg). Conventional machining removed 5,700 lb (2,586 kg), meaning only 5% remained in the finished component.

Although the remaining 95% can be recycled, the collection of the resulting manufacturing chips, their cleaning, transport, and reprocessing add costs, while the machining process consumes cutting tools, coolant, electricity, and machine time. Additive manufacturing can reduce such losses by producing near-net-shape structures, but powder preparation, printing time, heat treatment, machining, and inspection remain significant expenses. For Shenyang, the decisive industrial measures would likely be centered on machine occupancy, material utilization, fusion-joining time, rejection rates, and the number of assembly operations eliminated. However, producing 3D-printed primary aircraft structures also requires more demanding qualification than just manufacturing secondary brackets or tools.

Why 3D-printed fighter structures require extensive fatigue testing

Powder quality, layer bonding, build orientation, internal porosity, and residual stresses all affect mechanical properties, while surface defects can initiate fatigue cracks under repeated loading. Unlike a conventional forged component, a printed structure can exhibit directional variations in mechanical properties because its material is deposited and fused through successive layers, unlike a block of metal. Qualification of large printed structures and fusion-joined sections therefore requires more static-load testing, fatigue testing, damage-tolerance assessment, dimensional verification and nondestructive inspection, together with heat treatment and machining where necessary. They also affect maintenance: a consolidated structure can eliminate fasteners and reduce inspection points, but damage to one section may require a more complicated repair or the replacement of a larger assembly.

However, additive manufacturing could also shorten replacement times for qualified brackets, ducts, fittings and selected engine parts, particularly when conventional production requires dedicated tooling, as seen on U.S. submarines. For China's J-35, Shenyang's advances are consequently and potentially relevant to the structural demands of carrier operations aboard the Fujian (Hull 18), where electromagnetic catapult launches and arrested recoveries impose repeated acceleration and deceleration loads on the navalized J-35 Blue Shark.

What Shenyang's 3D printing advances could potentially bring to the J-35 and future Chinese fighters

A five-meter integrated fuselage structure could reduce the number of mechanical joints in selected load-bearing assemblies, while the annular heat exchanger could combine cooling, airflow and structural functions within the limited space available around an engine intake. These manufacturing options are also relevant to this stealth aircraft, which must accommodate internal weapons bays, fuel tanks, sensors and electronic equipment without altering its external geometry. Shenyang's six additive manufacturing processes, 13 metal materials and 19 component categories consequently provide several manufacturing options.

Still, their potential use on the J-35 would depend on qualification, repeatability, inspection throughput and integration with conventional manufacturing. In short, the AVIC announcement establishes its ability to manufacture larger and more complex aircraft components, with potential relevance to the J-35 and the future J-36 and J-50 six-gen aircraft, but this advantage will ultimately depend on the number of qualified components incorporated and the measured savings achieved across both complete production and maintenance cycles.


Explore More Defense News

• Land Defense News
• Naval Defense News
• Defense Aerospace News

Written by Jérôme Brahy - Defense Analyst

Jérôme Brahy is a defense analyst and documentalist at Army Recognition. He specializes in naval modernization, aviation, drones, armored vehicles, and artillery, focusing on strategic developments in the United States, China, Ukraine, Russia, South Korea, Türkiye, and Belgium. His analyses go beyond the facts, providing context, identifying key actors, and explaining why defense news matters globally.


Copyright © 2026 Army Recognition